Call: 260.495.9811Email: sales@reesinc.com
TERMS AND CONDITIONS

NOTE: Express orders - if need shipped out today, order must be placed by the following times:

UPS: 11:00 A.M. Eastern Time
FedEx: 11:00 A.M. Eastern Time
*Express shipping may not be available for all items
  • 30.5mmpbsum

    Features/Applications
    The following switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment. The body is made from die-cast zinc. The plungers are also made from diecast zinc with the 1.00 in. diameter style having a colored plastic (poly-carbonate) insert. The mushroom style plastic plunger heads are solid colors throughout. Each operator will accept up to three tiers of two contact blocks for a total of six separate circuits. Each operator is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these units is 1,000,000 operations. These devices can be found on a variety of machinery, used to perform such operations as ‘start’, ‘stop’, ‘top stop’,‘inch’, ‘on’, ‘off’, ‘forward’, ‘reverse’ etc.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • 30.5mm Mushroom and Rope Pull Operators 1

    Features/Applications
    The following switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment. The body is made from die-cast zinc. The zinc plated ring eye operator is also made from die-cast zinc. The mushroom ergonomic shaped plungers are molded from DuPont Delrin 100ST Acetal for improved impact resistance and are solid colors throughout. Each operator will accept up to three tiers of two contact blocks for a total of six separate blocks. Each operator is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these units is 1,000,000 operations. These devices can be found on a variety of machinery, used to perform such operations as ‘start’, ‘stop’, ‘top stop’, ‘inch’, ‘jog’, ‘on’, ‘off’, ‘forward’, ‘reverse’, etc.
    The 40102 series satisfies the requirements of IEC 60947-5-5 - 3.9 direct opening action (positive opening action) (of a contact element;) when fitted with one or more of any of our normally closed contact blocks. This is commonly referred to as “Positive Break”, meaning the breaking of the normally closed contacts in not dependant upon springs.
    Recommended cable length for the 40050 series is 33 feet.

    Designated switches have been certified as Emergency Stop Pushbuttons and are listed under UL/NISD File E357870, Sec. 1. These switches were evaluated for NISD mounted in a UL type 12/13 enclosure.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • Combined Selector Push button Control 1

    Features/Applications
    The following switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment. The body is made from die-cast zinc. The chrome plated knob and plunger are also made from die-cast zinc. Each operator will accept up to three tiers of two contact blocks for a total of six separate circuits. The device is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these units is 250,000 operations. A selector-push button operator combines the function of a single push button device with that of a selector in a single unit. Contact operation sequences are selected by rotating the knurled guard in the two available positions. When the position is selected, depressing the plunger will give contact operation as shown in the sequence chart.


    TO ORDER CORRECTLY SPECIFY THE FOLLOWING:
    Specify--> the Selector-Pushbutton operator
    Specify--> the choice of Cam (-501; or -502; or -506)
    Specify --> the Contact Block(s)
    EXAMPLE: 40302-501 Qty. 1
    50701-000 Qty. 1

  • Contact Blocks 1

    Features/Applications
    Features/Applications These contact blocks are designed for use on ALL REES push button operators and selector switches as shown on the preceding pages. The mechanical life of these devices is 1,000,000 operations. Each captive terminal on the contact block will accept (2) # 14 AWG stranded wires and the contacts are gold plated to eliminate high resistance tarnishing.
    The 52702 block consists of a B block (50702) attached to an adapter. This adapter Opens the NC contact of the B block Upon Removal from the switch operator. The OUR action provides an added level of security for instances where a NC block may be removed from the operator.

    Electrical Ratings
    “HEAVY DUTY - A600 / N150”
    Listed under UL 508 - File # E 58589;
    Certified under CSA C22.2 - File # LR 3648
    CE Compliant IEC/EN: 60947-5-1
    Third party certified under Test Report - E58589 - D2 - CB 

    Environmental Temperature Range
    Operating: +32°F to +131°F (0°C to +55°C)
    Storage: -40°F to +185°F (-40°C to +85°C)
    Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

    CAUTION:  NEVER EXCEED THREE TIERS IN STACKING BLOCKS.

    WARNING - DANGER

     

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

     

    ---------------------------------------------------------------------------------------------------------------------

     

    AVERTISSMENT - DANGER

     

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

     

     

     

  • Standard Pilot Lights

    Features/Applications
    The pilot light bodies are made from polycarbonate and are sonically welded together. The chrome plated zinc die cast housings will mount in a standard 30.5mm hole. They are environmentally rated NEMA 12/13. Each captive terminal on the terminal block will accept (2) # 14 AWG stranded wires. These lights are generally found on machine control panels as circuit/function indicators. The NPT mount styles compliment the self contained cable switches and are used extensively in that function. Replacement lamps and lenses can be found in the accessories section for 30.5mm devices.
    NOTE: Except where noted Lenses are NOT included with the pilot lights.

    Electrical Ratings
    Listed under UL 508 - File # E 58589;
    Certified under CSA C22.2 - File # LR 3648

    Environmental Temperature Range
    Operating: +32°F to +131°F (0°C to +55°C)
    Storage: -40°F to +185°F (-40°C to +85°C)
    Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • Miniature Pilot Lights 1

    Features/Applications
    The pilot light bodies are made from polycarbonate and are sonically welded together. The zinc die cast housings will mount in a 0.69 in. dia. hole. They are environmentally rated NEMA 12/13. Each captive terminal on the terminal block will accept (2) # 14 AWG stranded wires. These lights are generally found on machine control panels as circuit / function indicators. Replacement lamps and lenses can be found in the accessories, section, on pages 56 and 59, for 30.5mm devices.
    NOTE: Except where noted Lenses are NOT included with the pilot lights.

    Electrical Ratings
    Listed under UL 508 - File # E 58589;
    Certified under CSA C22.2 - File # LR 3648

    Environmental Temperature Range
    Operating: +32°F to +131°F (0°C to +55°C)
    Storage: -40°F to +185°F (-40°C to +85°C)
    Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • Image

    Features
    The one piece translucent plastic lenses are molded from high impact polycarbonate. The two piece (41252’s) lenses have a chrome plated zinc die cast base with a polycarbonate lens pressed into the end.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • Image

    Applications
    The following legend plates are designed to mount to the pilot lights or operators. Legend Plates are made from clear, red or black anodized aluminum.
    Specials
    Specify the 5 digit plate number plus the suffix number -000 plus your special marking. Example: “CLAMP” = 09013-000
    NOTE: Legend Plates are NOT included in the price of devices.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • 09010-001

    Applications
    The following legend plates are designed to mount to the pilot lights or operators. Legend Plates are made from clear, red or black anodized aluminum.
    NOTE: Legend Plates are NOT included in the price of devices.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

^