Features/Applications
The following selector switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment. The die-cast zinc body, is painted with a dry powder paint. The die-cast zinc wing lever is either painted black or nickel plated. Each terminal will accept (2) #14 AWG stranded wires. The switches are supplied with all mounting hardware and a solid santoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these devices is 500,000 operations. These switches can be found on a wide variety of machinery. Their rugged construction and long term reliability make these switches extremely well suited to function within various industrial conditions.

Electrical Ratings
"HEAVY DUTY - A600 / N300”
Listed under UL 508 - File # E 58589
Certified under CSA C22.2 - File # LR 3648
CE Compliant EN 60947-5-1

Environmental Temperature Range
Operating: +32°F to +131°F (0°C to +55°C)
Storage: -40°F to +185°F (-40°C to +85°C)
Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Features/Applications
The following selector NEMA 12/13, IP65 switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment. The die-cast zinc body, is painted with a dry powder paint. The die-cast zinc wing lever is either painted black or nickel plated. Each terminal will accept (2) #14 AWG stranded wires. The switches are supplied with all mounting hardware and a solid santoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these devices is 500,000 operations. These switches can be found on a wide variety of machinery. Their rugged construction and long term reliability make these switches extremely well suited to function within various industrial conditions.

Electrical Ratings
"HEAVY DUTY - A600 / N300”
See attached Chart
Certified under CSA C22.2 - File # LR 3648

Environmental Temperature Range
Operating: +32°F to +131°F (0°C to +55°C)
Storage: -40°F to +185°F (-40°C to +85°C)
Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

Note:  This is an example only



Note: Legend Plates are REQUIRED and CANNOT be added after the switch is assembled.
Legend wording MUST be specified when ordering the switch.
Legend “OFF, INCH, SINGLE STROKE, CONT.” is a Standard - ALL others are Specials.

Note:  A worksheet is available in the Downloads section at right on individual item page.

To use this worksheet: 
Determine from your circuit diagram the number of positions desired and the number of circuits to be controlled. Place an “X” to indicate what contacts should be closed in which position. Contacts are normally continuously closed in consecutive positions. Refer to the example above. Omit the vertical line if contacts are open between consecutive positions.

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Features/Applications
The following selector switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment. The die-cast zinc body, is painted with a dry powder paint. The die-cast zinc wing lever is either painted black or nickel plated. Each terminal will accept (2) #14 AWG stranded wires. The switches are supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation. The mechanical life of these devices is 500,000 operations. These switches can be found on a wide variety of machinery. Their rugged construction and long term reliability make these switches extremely well suited to function within various industrial conditions.

Electrical Ratings
See attached Chart
Listed under UL 508 - File # E 58589;
Certified under CSA C22.2 - File # LR 3648

Environmental Temperature Range
Operating: +32°F to +131°F (0°C to +55°C)
Storage: -40°F to +185°F (-40°C to +85°C)
Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

Features/Applications
The following enclosures are made from 14 GA. sheet steel painted with a dry powder paint. The first group will accept all standard size REES push button switches. The second group (the 04938-’s) are designed to fit the larger style switches from page 18. The 02765-100 one opening, painted yellow, is suitable for holding an “Emergency Stop” switch. These enclosures can be used to house any switch that has the same mounting pattern.

These enclosures are rated Nema 12/13, IP 65.

Note: When mounting a Rees lockable switch on one of these enclosures you may need to order our gasket “spacer”, part number 01004-045, for additional room to add the lock.

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Features/Applications

The following guards are designed to mount to the single or double plunger push button switches.  They are die cast from a high strength zinc alloy (Zamac #3).

• Additional length mounting screws are provided with each guard.
• Series 09002 legend plates can be mounted on these ring guards. 

The usage chart below shows the minimum recommended guard to use to provide protection against inadvertent actuation caused by accidental contact of the switch plunger.  Use of a taller guard is an acceptable alternate method.

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Features/Applications
The Palm Switch Guard / Actuator is designed to replace the ring guard on REES palm operated switches. It features sturdy zinc die cast and steel, both are painted with dry powder paint. It has a large operating pad which reduces the activation force on the center of the hand and directly on the ulnar artery and median nerve where they pass through the palm. There is less potential compression to the hand if the outer part of the palm is used to depress the switch. A study by the ergonomic consulting firm “Human Dynamics, Lancaster, OH,” found that both resistance and travel play important roles in control design. Travel provides the user with sense of movement and position. When associated with resistance, such movement provides tactile feedback about control activation.This feedback helps the operators perception and increases accuracy, safety and efficiency. Tactile feed back lets the operator know that the switch has been activated because they can ‘feel’ the switch working. On switching devices without feedback operators tend to push harder causing muscle fatigue and increasing the risk of injury. Also, a comfortable and lower trip force is created by the mechanical advantage of the actuator’s design.

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Features/Applications
The following legend plates are designed to mount to the single or double plunger pushbuttons and ring guards. Legend Plates are made from clear anodized aluminum with black lettering.

Legend Plates are NOT included in the price of devices.
To Order Legend Plates:
Standards
Specify the 5 digit plate number plus the 3 digit suffix number from the chart below. Example: “START” = 09001-005
Specials
Specify the 5 digit plate number plus the suffix number -000 plus your special marking. Example: “BY-PASS” = 09001-000

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.