Call: 260.495.9811Email: sales@reesinc.com
TERMS AND CONDITIONS

NOTE: Express orders - if need shipped out today, order must be placed by the following times:

UPS: 1:00 P.M. Eastern Time
FedEx: 12:00 P.M. Eastern Time

Features/Applications

The following switch is a hand operated, control circuit device, rated ‘Heavy Duty’ normally for use with electromagnetic equipment.  The body is made from die-cast zinc.  The red mushroom ergonomic shaped plunger is molded from DuPont Delrin 100ST Acetal for improved impact resistance and is solid color throughout.    

 

  • UL/NISD E357870
  • Nema 12/13, IP 65
  • Positive Break, Gold Plated Contacts
  • Sliding Padlock Attachment 

The operator will accept up to three tiers of two contact blocks for a total of six separate circuits.  Each operator is supplied with all mounting hardware and a solid neoprene rubber gasket which provides an oil tight seal upon installation.  The mechanical life of this unit is 1,000,000 operations. 

 

This device can be found on a variety of machinery, used to perform such operations as ‘stop’, ‘top stop’, ‘off’, ‘forward’, ‘reverse’, etc.

 

This series satisfies the requirements of IEC 60947-5-5 – 3.9 direct opening action (positive opening action) (of a contact element); when fitted with one or more of any of our normally closed contact blocks.  This is commonly referred to as “Positive Break”, meaning the breaking of the normally closed contacts is not dependent upon springs.

 

Electrical Ratings

“HEAVY DUTY – A600 / N150”

 

Environmental Temperature Range

Operating:  +32oF to +131oF (0oC to +55oC)

Storage:  -40oF to +185oF (-40oC to +85oC)

Note:  Operating temperatures at 0oC are based on the absence of freezing moisture and liquids.

 

Normal Potential

Normal Current

Inrush Current

110-120 aca volts

6.0 amp.

60.0 amp.

220-240 aca

3.0 amp.

30.0 amp.

440-480 aca

1.5 amp.

15.0 amp.

550-600 aca

1.2 amp.

12.0 amp.

115-125 dcb

2.2 amp.

-----

230-250 dcb

1.1 amp.

-----

a  Power factor 0.35 or less

b  Inductive loads as specified in Section 125 of Industrial

   Control Devices, Controllers and Assemblies, ANSI /

   NEMA ICS 2-1988

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Unit of Measure

Specifications

Operator Color

N/A Red

Operator Material, Size, Style

N/A 2.00 in. Plastic Mushroom

Padlock Feature

N/A Yes

Switch Type

N/A Maintained
UL/NISD

Positive Opening Contact

N/A
 

Contact
Block(s)
Included

N/A 50703-NO/NC

Operating Force

N/A 8.0 lb

Approx. Shipping Weight

N/A 0.80 lb

Plunger Head Operator Replacement

N/A 43200-042

Old Catalog Number

N/A R102

Operating Type

N/A Maintained
^