Call: 260.495.9811Email:

NOTE: Express orders - if need shipped out today, order must be placed by the following times:

UPS: 1:00 P.M. Eastern Time
FedEx: 12:00 P.M. Eastern Time
  • Image

    Replacement parts for use on 04944 switches. Two zinc ring eye halves with zinc plated steel screws.

  • Arm Kit

    Replacement parts for use on 04945 switches. Included is the arm and ALL associated hardware.

  • Tee Handle

    Replacement part for use on 04944 switches. Zinc T-Handle with zinc plated steel screw.

  • Image

    For tension adjustment on cable runs. Aluminum body with zinc plated steel eyebolts.

  • Image

    Galvanized Steel
    (7x7) Aircraft Cable Used for cable runs.
    3/16" O.D.
    0.028 lbs./Ft.

  • Image

    Use with aircraft cable to reduce breakage at the end. Steel, zinc plated.

  • Image

    Use with aircraft cable to secure the cable end. Cast Malleable Iron Body, Natural Finish with Steel U-Bolt & nuts, Natural Finish.

  • Image

    Use with aircraft cable to extend, splice the cable.

  • Image

    Used in cable run to reduce slack between supports. Spring Rate = 50 lbs./in. Music wire, zinc plated.

  • Image

    Used to support the cable run at intervals. The kit includes one zinc plated steel eyebolt, two nuts and a lock washer.

  • Image

    Replacement parts for use on 04945 switches. The kit includes two nickel coated stainless steel springs.

  • Image

    Replacement parts for use on 04953 and 04954 switches.
    The kit includes one flag and two mounting screws.

  • Image
  • Image

    May be used to replace gaskets on cable switch series 04944, 04953 and 04954.

  • Image

    Use with 04944 and 04962 switches to mount in place of old styles 02669; 03030; or 04935.

  • Standard Pilot Lights

    The pilot light bodies are made from polycarbonate and are sonically welded together. The chrome plated zinc die cast housings will mount in a standard 30.5mm hole. They are environmentally rated NEMA 12/13. Each captive terminal on the terminal block will accept (2) # 14 AWG stranded wires. These lights are generally found on machine control panels as circuit/function indicators. The NPT mount styles compliment the self contained cable switches and are used extensively in that function. Replacement lamps and lenses can be found in the accessories section for 30.5mm devices.
    NOTE: Except where noted Lenses are NOT included with the pilot lights.

    Electrical Ratings
    Listed under UL 508 - File # E 58589;
    Certified under CSA C22.2 - File # LR 3648

    Environmental Temperature Range
    Operating: +32°F to +131°F (0°C to +55°C)
    Storage: -40°F to +185°F (-40°C to +85°C)
    Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.


    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.



    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • Lexan housing only No bulb, no lens 1/2 NPT mounting

  • Cable/Handle Assembly 02005-840

    • 10' Vinyl Covered (7x7) Steel Cable.
    • 1 7/8" Diameter Ball Handle
    • Thimble, Strain Relief
    • Two Rope Clips
    • 0.65 lb. Total Assembly Weight

  • 02005-563
  • 02005562

    Replacement cover with blue reset button for 04962 & 04964 series.

  • 02005-600

    3/4" to 1/2" Bushing to be used on products with a 3/4" NPT conduit opening.