Call: 260.495.9811Email: sales@reesinc.com
TERMS AND CONDITIONS

NOTE: Express orders - if need shipped out today, order must be placed by the following times:

UPS: 11:00 A.M. Eastern Time
FedEx: 11:00 A.M. Eastern Time
*Express shipping may not be available for all items

Features/Applications

The following switch is a hand operated, spring latchable, control circuit device, rated ‘Heavy Duty’ normally for use with electromagnetic equipment.  The body, painted with a dry powder paint, is made from die-cast zinc.  The plastic plunger is molded from DuPont Delrin 100ST Acetal for improved impact resistance and is solid color throughout. 

 

  • Gold plated contacts eliminate high resistance tarnishing
  • Complies with IEC/EN 60947-5-5 for ‘emergency stop’ applications
  • Nema 12/13, IP 65 

Each captive terminal will accept (2) #14 AWG stranded wires.  Each switch is supplied with all mounting hardware and a solid santoprene rubber gasket which provides an oil tight seal upon installation.  The mechanical life of this device is 500,000 operations. 

 

This switch can be found in a variety of uses on industrial machines.  Presses and press brakes use them as “STOP” buttons.

 

Electrical Ratings

“HEAVY DUTY – A600 / N300”

Listed under UL 508 – File # E 58589

Certified under CSA C22.2 – File # LR 3648

CE Compliant IEC/EN 60947-5-5

 

Environmental Temperature Range

Operating:  +32oF to +131oF (0oC to +55oC)

Storage:  -40oF to +185oF (-40oC to +85oC)

Note:  Operating temperatures at 0oC are based on the absence of freezing moisture and liquids.

 

Normal Potential

Normal Current

Inrush Current

110-120 aca volts

6.0 amp.

60.0 amp.

220-240 aca

3.0 amp.

30.0 amp.

440-480 aca

1.5 amp.

15.0 amp.

550-600 aca

1.2 amp.

12.0 amp.

115-125 dcb

2.2 amp.

-----

230-250 dcb

1.1 amp.

-----

a  Power factor 0.35 or less

b  Inductive loads as specified in Section 125 of Industrial

   Control Devices, Controllers and Assemblies, ANSI /

   NEMA ICS 2-1988

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

Unit of Measure

Specifications

Plunger Color

N/A Red

Cover Color

N/A Yellow

Operating Force

N/A 12.5 lb

Latch/Plunger Operation

N/A Latches when depressed Operate latch to release

Positive Opening Contact

N/A
 

Contact Arrangement

N/A #09 NO + NC

Contact Type

N/A Slow-Make Slow-Break

Approx. Shipping Weight

N/A 1.65 lb

Old Catalog Number

N/A 664

Switches comply with

N/A IEC/EN 60947-5-5 for Emergency Stop Applications
^