Call: 260.495.9811Email: sales@reesinc.com
  • 22.5 mm Control Units

    Features/Applications

    Available in Lockable, Push-Pull, and Momentary versions, the following switches are hand operated, control circuit devices, rated ‘Heavy Duty’ normally for use with electromagnetic equipment.  The body is made from die-cast zinc.  The mushroom shaped plungers are molded from DuPont Delrin 100ST Acetal for improved impact resistance and are solid colors throughout.

     

    • Nema 12/13, IP 65
    • Gold Plated Contacts

    Each operator will accept up to three tiers of two contact blocks for a total of six separate blocks.  Each operator is supplied with all mounting hardware and a Buna-N (NBR) o-ring which provides an oil tight seal upon installation.  The mechanical life of these units is 1,000,000 operations. 

     

    These devices can be found on a variety of machinery, used to perform such operations as ‘start’, ‘stop’, ‘top stop’, ‘inch’, ‘jog’, ‘on’, ‘off’, ‘forward’, ‘reverse’, etc.

    The 22102 series satisfies the requirements of IEC 60947-5-5 – 3.9 direct opening action (positive opening action) (of a contact element); when one or more of any of our normally closed contact blocks are fitted on any red operator.  This is commonly referred to as “Positive Break”, meaning the breaking of the normally closed contact(s) is not dependent upon springs.

    Designated switches have been certified as Emergency Stop Pushbuttons and are listed under UL/NISD File E357870, Sec. 1. These switches were evaluated for NISD mounted in a UL type 12/13 enclosure.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

  • Contact Blocks 1

    Features/Applications
    Features/Applications These NEMA 12/13, IP65 contact blocks are designed for use on ALL REES push button operators and selector switches as shown on the preceding pages. The mechanical life of these devices is 1,000,000 operations. Each captive terminal on the contact block will accept (2) # 14 AWG stranded wires and the contacts are gold plated to eliminate high resistance tarnishing.
    The 52702 block consists of a B block (50702) attached to an adapter. This adapter Opens the NC contact of the B block Upon Removal from the switch operator. The OUR action provides an added level of security for instances where a NC block may be removed from the operator.

    Electrical Ratings
    “HEAVY DUTY - A600 / N150”
    Listed under UL 508 - File # E 58589;
    Certified under CSA C22.2 - File # LR 3648
    CE Compliant IEC/EN: 60947-5-1
    Third party certified under Test Report - E58589 - D2 - CB 

    Environmental Temperature Range
    Operating: +32°F to +131°F (0°C to +55°C)
    Storage: -40°F to +185°F (-40°C to +85°C)
    Note: Operating temperatures at 0°C are based on the absence of freezing moisture and liquids.

    CAUTION:  NEVER EXCEED THREE TIERS IN STACKING BLOCKS.

    WARNING - DANGER

    These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

    ---------------------------------------------------------------------------------------------------------------------

    AVERTISSMENT - DANGER

    Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.


     

  • 09022-004
^