Call: 260.495.9811Email: sales@reesinc.com
TERMS AND CONDITIONS

NOTE: Express orders - if need shipped out today, order must be placed by the following times:

UPS: 11:00 A.M. Eastern Time
FedEx: 11:00 A.M. Eastern Time
*Express shipping may not be available for all items

These slack cable style switches are equipped with a positive safety lock.  Once actuated, they cannot be accidentally reset causing dangerous equipment to restart. 

 

The cable may be extended in either or both directions with no changes required in the internal mechanism.  There is one electrical connection inside eliminating the double electrical connections typically required in two ended units employing a separate micro switch for cable in each direction. 

 

The actuation force required is simply adjusted in the field by attaching the cable to any one of the three holes provided on the switch actuating arm.

 

The standard construction of these switches consists of the corrosion resistant aluminum housing complete with stainless steel hardware, red powder coated actuation handle and stainless steel actuation shaft. 

 

These switches are usually installed with cable running in both directions from the crank type actuating arm. The cable should be supported by eyebolts every 10 feet to ensure that the weight of the cable alone will not actuate the switch. 

 

  • Recommended cable length is 100 feet maximum on each end.
  • Can be mounted in any position

A pull on the cable at any point will rotate the red actuation arm 60 degrees. The actuation arm will end in a position that is easily seen from a distance, thus identifying the actuated unit. Two spring loaded detents riding on a hardened steel cam provide resistance to arm rotation.  When the actuation force overcomes this resistance the assembly rotates 60 degrees and is locked in place by the detents. Affixed to the rotating shaft is a cam mechanism which actuates up to two micro switches during rotation.  The micro switches are held in the actuated position by the detents.



 

WARNING - DANGER

These products should only be used where point-of-operation guarding devices have been properly installed & maintained so that appropriate OSHA and ANSI B11.1 regulations & standards are met.  Misapplication of the products on machinery lacking effective point-of operation safeguards can cause serious injury to the operator of that machinery.

---------------------------------------------------------------------------------------------------------------------

AVERTISSMENT - DANGER

Ces produit doivent seulement être utilisés sur des postes à risque correctement sécurisés et entretenus afin d’être conforme aux standards et régulations en vigueur (CSA, CLC). Un mauvais usage de ces produits sur des machines et des postes de travail non sécurisés de manière efficace peut causer des blessures graves au technicien maniant ces machines.

1 - 2 of 2 | Results Per Page | View | Unit of Measure
1 

Item #

Item Photo

Contact Arrangement

FT Trip Force

SD=5ft./1.5m (FO)

SD=5ft./1.5m (ST**)

SD=10ft./3.0m (FO)

SD=10ft./3.0m (ST)

Add To Cart/Request Quote
Sort by

04965-000
N/A 1 (NO/NC) SPDT N/A 20-40 lb9.1-18.1 kg N/A 10-20 lb4.5-9.1 kg N/A 7.7-10.2 in19.6-25.8 cm N/A 7.5-15 lb3.4-6.8 kg N/A 10.8-14.3 in27.4-36.3 cm Add To Cart
Request Quote

04965-200
N/A 2 (NO/NC) SPDT N/A 20-40 lb9.1-18.1 kg N/A 10-20 lb4.5-9.1 kg N/A 7.7-10.2 in19.6-25.8 cm N/A 7.5-15 lb3.4-6.8 kg N/A 10.8-14.3 in27.4-36.3 cm Add To Cart
Request Quote
1 - 2 of 2 | Results Per Page | View | Unit of Measure
1 
^